吸式干澀機

◆成品的特點 Product features

※含有穩定可靠保持一致的排氣壓和露點

1.離心分離塔之長度與截面積經調查但是精密模具統計，塔床水頭損失小， 保障了再壓縮汽體吹干劑5秒的接觸到耗時，考慮原材料氣的露點標準。

2.30％的干熱劑裕量，使用賠償干熱劑的自然美老化試驗，加強組織領導干熱。

3.特大型粘附器，為了保證暖濕氣流不均可以通過變干劑層，消減溝流后果。

※凈化氣量損耗量不大于14％

1.領航的機筒來設計，上傳100％的吸出形成，儲放的形成適用加大二次利用時段的二次利用氣攝氏度，不斷提高專用設備的解吸效率，會讓二次利用更徹底消除。

2.吹干和重復利用運用選擇性自然通風工作方案，濕空氣的流回干的過濾劑時效性果比較好。重復利用氣出口貿易含濕量操作在亞飽滿睡眠狀態，使消音器及排氣管檢修通道無起霜之慮。

3.可利用晾干機的行駛電流要調整重復能力能力氣劑量，保證重復能力能力氣旋累計平穩，重復能力能力壓強低至臨介。

※烘干劑用生存期長

1.適合的的機筒尺寸大小，使氣體經過干熱劑層的流動速度和期限增加好的壯態，充分地充分利用干熱劑的穩定性。

2.適度的系統的增加，在熱空氣入駐機筒前，經除油治理適時去掉熱空氣中內動植物油物與重破壞物，解決非常干燥劑層受破壞。

※環保設備選用了構思高品行電動及液壓閥和靠譜的全電子器件可代碼編程序智能控制器，組隊軟件界面團結，會自動多次表現雙塔工程狀況，間歇周期公式活動現場可編，出廠的選用10min。調節閥期限歷時50萬次操作。

※封頭表面作冷鍍鋅鋼防腐防銹治療，10年不生銹。

※運動較準、功效穩定性、操作的簡便計算，的安裝不同條件。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆大部分枝術數據 Main technical parameters